Drag[en]gine Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
{{tag>graphic skin texture absorption}}
<WRAP youarehere>
[[:start|Start Page]] >> [[:gamedev|Game Development with the Drag[en]gine]] >> [[gamedev:skinproperties|Skin Texture Properties]] >> [[gamedev:texturepropertylist|Texture Property Database]] >> **absorption.range**
</WRAP>

====== Skin Texture Property: absorption.range ======

Defines the sub surface absorption range as typically used for human skin.

|Excepted Data Source|1 component value|
|Data Range|0 or grater|
|Default Value|0|
|Affected Modules|Graphic|
|Linked Properties|[[absorption|absorption]]|

====== Description ======

The **absorption.range** texture property defines the range of scattering in sub surface absorption of a material. Sub surface absorption affects light entering the material after surface based texture properties have taken effect. Sub surface absorption has two main effects. The first is that light is scattered under the surface and exits at a nearby point. The second effect is translucency. In both cases the **absorption.range** texture property defines the range of absorption. Beyond this limit the light is fully absorbed by the material. In between the light is partially absorbed using an exponential decay function. In contrast to the [[absorption|absorption]] texture property the **absorption.range** is a single component value and defines the largest radius. The actual absorption used is thus [[absorption|absorption]] times **absorption.range** component wise. See [[absorption|absorption]] texture property more information about absorption.

The source is a value with 1 color component with values 0 or greater.

The default value for this texture property is 0 which disables sub surface light absorption and scattering.

A value of 0.02 is a typical choice for human skin. Most materials have absorption ranges below 0.1 .

Note on the values in the examples below. The stanford armadillo model is small. If you want a full size 2 meter high armadillo to show these absorption properties you have to multiply the range by 10 to obtain similar values.

====== Examples ======

<WRAP column 45%>
<WRAP center box 350px>
{{ :gamedev:textureproperties:absorption_4.jpg?direct&300 |Stanford armadillo with 0 absorption range and back-lit.}}
<WRAP centeralign>Stanford armadillo with 0 absorption range and back-lit. No light penetrates in this situation. A good choice for solid materials like stone.</WRAP>
</WRAP>
</WRAP>

<WRAP column 45%>
<WRAP center box 350px>
{{ :gamedev:textureproperties:absorption_5.jpg?direct&300 |Stanford armadillo with 0.02 absorption range and back-lit.}}
<WRAP centeralign>Stanford armadillo with 0.02 absorption range and back-lit. This matches human skin and yields translucency on extremities where geometry thickness is low.</WRAP>
</WRAP>
</WRAP>

<WRAP clear></WRAP>

<WRAP column 45%>
<WRAP center box 350px>
{{ :gamedev:textureproperties:absorption_6.jpg?direct&300 |Stanford armadillo with 0.05 absorption range and back-lit.}}
<WRAP centeralign>Stanford armadillo with 0.05 absorption range and back-lit. With larger radius value light starts to penetrate also thicker geometry like the legs.</WRAP>
</WRAP>
</WRAP>

<WRAP column 45%>
<WRAP center box 350px>
{{ :gamedev:textureproperties:absorption_7.jpg?direct&300 |Stanford armadillo with 0.2 absorption range and back-lit.}}
<WRAP centeralign>Stanford armadillo with 0.2 absorption range and back-lit. Extreme radius example resulting in heavy light penetration. This one looks like jelly doesn't it?</WRAP>
</WRAP>
</WRAP>

<WRAP clear></WRAP>
Drag[en]gine Wiki

User Tools

Site Tools

Page Tools
