Drag[en]gine Wiki

User Tools

Site Tools

Trace:
democap:tutorialcapturing

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
democap:tutorialcapturing [2022/01/31 18:23] – dragonlorddemocap:tutorialcapturing [2025/04/06 19:28] (current) – [Calibrate] dragonlord
Line 12: Line 12:
 \\ \\
 {{ :democap:ui_panel_session.png }} {{ :democap:ui_panel_session.png }}
-</WRAP> 
- 
-<WRAP center round info 60%> 
-Since version 0.4 the panel has been split up. See [[democap:uipanelcharacter|Panel Character]] and [[democap:uipanelcapture|Panel Capture]] to locate the widgets. 
 </WRAP> </WRAP>
  
Line 28: Line 24:
    * Click <wrap em><wrap hi>Calibrate</wrap></wrap> to start the calibration process.    * Click <wrap em><wrap hi>Calibrate</wrap></wrap> to start the calibration process.
    * Put on the HMD. The instructions are shown.    * Put on the HMD. The instructions are shown.
-   * Place your feet parallel to each other (not angled) leaving roughly two feet space between them.+   * Place your feet parallel to each other (not angled) nearly touching each other.
    * Strike a T-Pose with your arms spread sidewards.    * Strike a T-Pose with your arms spread sidewards.
-   * Point your thumbs forward. In this pose the palms face down and the back of the hand up.+   * Keep your controller in relaxed pose as if pointing to the side. In this pose the palms in your curled hand points forward.
    * Look straight ahead.    * Look straight ahead.
-   * Pull and hold either the left or right hand controller <key>Trigger</key> for 1 second. The progress bar fills up during this time. To cancel calibration release the trigger before the bar fills up. +   * Pull and release either the left or right hand controller <key>Trigger</key> to start the calibration warm-up phase. The warm-up phase is not used for calibration and is present to allow your hands to return to a steady position after pulling and releasing the trigger. This produces better results than keeping the trigger pulled. After the warm-up progress bar fills up the actual calibration begins with the second progress bar filling up. Once filled the calibration is finished. To cancel calibration press  the menu button on either controller. 
-   * Once the bar filled up the overlay is hidden and the calibration is finished.+   * Once both bars filled up the overlay is hidden and the calibration is finished.
  
 The Character is now calibrated against the actor (yourself). You can now examine the result using the <wrap em><wrap hi>VR Mirror</wrap></wrap>. The Character is now calibrated against the actor (yourself). You can now examine the result using the <wrap em><wrap hi>VR Mirror</wrap></wrap>.
  
 You can trigger this process (select character and start calibration) from within VR view using the <wrap em><wrap hi>VR Menu</wrap></wrap>. You can trigger this process (select character and start calibration) from within VR view using the <wrap em><wrap hi>VR Menu</wrap></wrap>.
 +
 +<WRAP center round tip 60%>
 +You can quickly start calibration without using the VR menu by pressing the menu button on both controllers at the same time while pulling the trigger on both controllers. Hence pull and hold both triggers then press both menu buttons at the same time.
 +</WRAP>
  
 ===== Start Capturing ===== ===== Start Capturing =====
democap/tutorialcapturing.1643653424.txt.gz · Last modified: 2022/01/31 18:23 by dragonlord

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki